Towel Cabinet For Small Bathroom Top Factory

The cabinet is engineered for compact bathrooms where floor area is limited but storage demand remains constant. Its profile is optimized to fit within a 600 mm wide niche while providing vertical

Inquire Now

Description

Towel Cabinet for Small Bathroom – Factory‑Ready Design

The cabinet is engineered for compact bathrooms where floor area is limited but storage demand remains constant. Its profile is optimized to fit within a 600 mm wide niche while providing vertical storage for folded towels.

Dimensional Layout and Space Efficiency

Standard overall dimensions are 600 mm width × 1800 mm height × 200 mm depth, with a tolerance of ±2 mm on each axis. Interior clear opening measures 560 mm wide × 1650 mm high, allowing a stack of up to 12 standard bath towels without compression. The depth includes a 15 mm rear service gap for ventilation and wiring clearance.

Material Selection and Corrosion Resistance

Primary structure uses 0.8 mm thick AISI 304 stainless steel sheet, formed with a 3 mm bend radius to eliminate sharp edges. Surface treatment consists of a 60 µm epoxy‑polyester powder coating, rated for 500 h salt‑spray exposure per ASTM B117 before visible rust. All fasteners are A2‑70 stainless steel to prevent galvanic coupling.

Load Capacity and Structural Integrity

Each shelf is designed to support a uniformly distributed load of 15 kg, verified by finite‑element analysis showing maximum deflection under load of 0.4 mm (L/4500). The cabinet frame resists a lateral racking force of 250 N without permanent deformation, suitable for typical bathroom vibration levels.

Installation and Mounting Options

Mounting is accomplished through concealed brackets that transfer load directly to wall studs or concrete anchors. Three standard configurations are offered to match common substrate conditions.

Stud‑mount bracket – two M6 × 50 mm bolts, shear capacity 2.5 kN per bracket.
Concrete‑anchor bracket – two M8 × 70 mm sleeve anchors, pull‑out resistance 3.2 kN.
Adjustable rail system – allows horizontal positioning ±25 mm for uneven walls.

Ventilation and Hygiene Features

The rear panel incorporates a patterned perforation array with 2 mm diameter holes spaced at 10 mm centers, providing an open area of 18 % and facilitating passive airflow of approximately 0.03 m³/min per cabinet under natural convection. Interior surfaces are smooth‑finished to Ra ≤ 0.8 µm, enabling easy wipe‑down with standard cleaning agents.

Customization Parameters

Parameter	Typical Range	Notes
Overall Width	500 mm – 800 mm	Increment steps of 50 mm.
Overall Height	1500 mm – 2100 mm	Adjustable in 100 mm modules.
Shelf Count	2 – 5	Shelf spacing adjustable 250 mm–350 mm.
Door Type	Sliding, Hinged, Open‑front	Hardware includes soft‑close dampers.
Finish	Powder coat (RAL 9010, 9005, custom)	Optional antimicrobial additive.
Mounting Hardware	Stud, Concrete, Rail	Factory‑pre‑drilled holes.

Quality Control and Testing

Each unit undergoes a three‑stage inspection: dimensional verification using calibrated CMM (±0.1 mm tolerance), visual surface assessment under 500 lux illumination, and functional load testing where shelves are subjected to 1.5× rated load for 10 minutes. Salt‑spray testing is performed on a sample batch per lot to confirm coating integrity before shipment.

Applications in Small Bathroom Environments

In confined bathrooms, vertical storage reduces floor clutter while keeping towels within reach. The corrosion‑resistant construction withstands repeated exposure to humidity and cleaning chemicals, extending service life beyond typical powder‑coated steel units. Architects specify this cabinet for guest suites, en‑suite showers, and compact urban apartments where space planning is critical.

Frequently Asked Questions

Can dimensions be customized? Yes, width, height, and shelf count are adjustable within the ranges shown in the table; custom lengths require a new tooling quote.
What information is required before quotation? Provide required overall dimensions, preferred door type, finish color, and mounting condition (stud, concrete, or rail). A simple sketch or DXF file speeds up the process.
What materials are available? Standard is AISI 304 stainless steel with epoxy‑polyester powder coat; alternative grades (316L) or finishes (brushed satin) are offered on request.
How is quality inspected? Dimensional checks, visual inspection, load testing, and salt‑spray verification are performed per lot; test reports are available upon request.
What packaging methods are available? Units are packed in double‑wall corrugated cartons with corner protectors and PE foam edges; palletized shipments include stretch wrap and corner boards for export.
What is the typical production lead time? Standard configurations ship in 3–4 weeks after drawing approval; customized items typically require 5–6 weeks.